// PARTS
62PIECES
// 02_MANIFEST / WSV-05 / SPOTLIGHT_FRAMEPRINT_QUEUE_LIVE
FRAME
01 / 08
SCALE_REF
1 : 100
L × H · MM
168 × 130
VIEW
ELEV_A
// MATERIAL
RESIN8K MSLA
// FINISH
RAWUNPAINTED
// ASSEMBLY
CANO PINNING
// EDITION
200NUMBERED
// 01PROJECT_BRIEFING // WSV-05_RAWREV.04 · APR 2026
// 01
RAW_PRINT
A 62-part garage kit, 8K MSLA-printed in photopolymer resin. Supports cleaned by hand. Subtle layer lines remain — they prime out.
++++// 02
REFERENCE_ONLY
Supplied unpainted and unassembled. All painted images on this page are operator builds, for reference only — your kit ships raw.
++++// 03
TECHNICAL_PROJECT
Requires standard prep — light sanding, support nub cleanup, glue. No pinning required. Estimated 6–8 hours from box to primer-ready.
++++// 02REFERENCE_PLATES // OPERATOR_REFERENCE_BUILDS08 OF 08 · PAINTED EXAMPLES
FRAME_01ELEV_A
++++
FRAME_02ELEV_B
++++
FRAME_03TOP_A
++++
FRAME_04TOP_B
++++
FRAME_05FRONT_A
++++
FRAME_06FRONT_B
++++
FRAME_07DETAIL_A
++++
FRAME_08DETAIL_B
++++// 03TECHNICAL_DOSSIERREV.04
// PHYSICAL
PART_COUNT
62 PIECES
DIMENSIONS_L
168mm
DIMENSIONS_H
130mm
SCALE
1:100 FIXED
EST_WEIGHT
~180g (BUILT)
EDITION_SIZE
200 NUMBERED
// PROCESS
MATERIAL
PHOTOPOLYMER RESIN · 8K MSLA
FINISH
RAW / UNPAINTED
SURFACE
SUPPORT-CLEANED · SUBTLE LAYER LINES
ASSEMBLY
CYANOACRYLATE (GLUE)
PINNING
NOT REQUIRED
PREP_TIME
6-8 HOURS (EST.)
// 04PARTS_BREAKDOWN // 62_PIECES_GROUPEDSUB_ASSEMBLIES
CHASSIS_CORE18/ 62
load-bearing armature, internal frame
++++ARMAMENTS14/ 62
rifles, mounts, magazines, sights
++++CABLING12/ 62
hydraulic lines, hoses, conduits
++++ARMOR_PLATING10/ 62
shoulder plates, side panels, greaves
++++ARTICULATION6/ 62
pivots, ball joints, retention pegs
++++DETAIL_PIECES2/ 62
operator hatch, antenna
++++// 05THE_COLLABORATOR // DETHKLAW_MINIATURES
DK
// PORTRAIT_PENDING
// STUDIO_DOSSIER
DethKlaw Miniatures
SCULPTOR · DIGITAL · BERLIN_DE · EST. 2019
Independent digital sculptor working in industrial-fiction silhouettes. Known for load-bearing armatures, exposed cabling, and a refusal to soften hard edges in service of “approachable” silhouettes.
WSV-05 is the first Mini Mecha collaboration — designed to print clean on standard MSLA hardware, with part separation and support orientation worked through across eleven test prints before final master release.
// 06BUILD_PROTOCOL // BOX_TO_PRIMEREST. 6-8H TOTAL
STAGE_0115min
UNBOX
Verify part count against included manifest sheet. Inspect for shipping damage. Photograph any defects within 7 days for replacement.
++++STAGE_021.5h
CLEAN
Light sanding of pre-clipped support nubs. Warm soapy bath to remove release agents. Pat dry; air-cure 30 min before priming.
++++STAGE_032h
PREP
Dry-fit all sub-assemblies before glue. Resin tolerances are tight — check for warp, gentle heat-correct if needed. Mask seam lines you intend to fill.
++++STAGE_043-4h
ASSEMBLE
Cyanoacrylate (medium viscosity) on all permanent joints. Articulation pegs are friction-fit — do not glue. Allow 24h full cure before primer.
++++// 07RELATED_DEPLOYMENTS // WSV-05_BUILDS3 ENTRIES · SEE_ALL_IN_ARCHIVE
MORITAKECOMMANDER
Zenithal pre-shade · oil pin wash · MIG pigments
♥ 1,208 · 11 PHOTOS1d AGO
KWAME_OCOMMANDER
Full scratch interior · LED install · brass etch
♥ 2,104 · 14 PHOTOS2d AGO
ASH_QOPERATOR
Monochrome · gloss seal only
♥ 289 · 3 PHOTOS6d AGO
// UNIT_LOCK_AT_RESERVATION
WSV-05 · ED.01
// REMAINING
200 / 200
// SHIP_WINDOW
JUN 06 · 2026
// UNIT_COST
$69.00